Imx219 board setup failed. 287161] imx219 8-0010: imx219_board_setup: error during i2c read prob...

Imx219 board setup failed. 287161] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1. 📌 Setup Board: RK1808 (custom device tree) Kernel: Dec 14, 2023 · I have been trying to use an imx219 camera with the J401 board. Nov 23, 2020 · Hi - I just received my jetson nano 2gb a few days ago and I have not been able to establish a connection with a camera through the MIPI CSI-2 port. 323835] imx219 7-0010: imx219_b Jan 5, 2022 · Nano series detect IMX219 camera sensor by default, this is expected if you have camera device disconnected. Is there documentation available that explains the process? Thanks in advance! [ 1. furthermore, this error logs won’t make the linux boot stuck. Jun 9, 2025 · Hi, I'm trying to enable and use the IMX219 camera module on a Rockchip RK1808 board, but I'm encountering problems during the driver probe stage. Jul 16, 2021 · Hi all, I've been trying to use this board with my IMX219 camera (it works with the Jetson Nano DevKit) to no avail. 217600] imx219 6-0010: tegracam sensor driver:imx219_v2. 287283] imx219: probe of 8-0010 failed with error -121 I attempted to install the arducam drivers as I initially thought that was the issue. I want to get the video stream from a B0183 camera with a IMX219 sensor to Opencv. Ok. I’m using an HDMI to CSI-2 module and I’ve verified connectivity and o… Jun 9, 2025 · Hi, I'm trying to enable and use the IMX219 camera module on a Rockchip RK1808 board, but I'm encountering problems during the driver probe stage. May 7, 2021 · Looks like the imx219 warning message not the key for boot failed. 1) Flashing the Module via SDKManager (Jetpack 4. 175793] tegradc tegradc. 6 [ 162. 4 (Beta) for Jetson Xavier NX) command: sudo . 360804] tegra-vii2c 546c0000. This resulted in a similar but different error (probe failed). 4. disable_fw_kms_setup=1 # Run in 64-bit mode arm_64bit=1 # Disable compensation for displays with overscan disable_overscan=1 # Run as fast as firmware / board allows arm_boost=1 [cm4] # Enable host mode on the 2711 built-in XHCI USB controller. I’m new to this so not sure how to update the device tree and driver. 0. 1: dpd enable lookup fail:-19 [1. 5. Not sure but looks like network case the system can’t boot. 287198] imx219 8-0010: board setup failed [ 1. 980326] imx219 9-0010: imx219_boa… Apr 17, 2022 · Jetson boots with this error message [ 1. I have succeeded to do it on my Jetson NX devkit. I can see the camera on /dev/video0. Mar 30, 2022 · Thank you very much for the image! I used balenaEtcher to flash this image to a 128GB SD Card, but I can't boot my Jetson Nano B01 4GB, it shows: [1. 1) and updating kernel via BSP (version R1. The /dev/video* file does not exists, and dmesg reads: 69676] imx219 9-0010: tegracam sensor driver:imx219_v2. 📌 Setup Board: RK1808 (custom device tree) Kernel: Feb 22, 2023 · The default JetPack image is done like that so the IMX219 is supported right out-of-the-box. Now, if you have tried many things like change to another connector in the devkit, have another camera module connected or replace the ribbon cable – then that suggests there is a hardware problem. Am using imx219 camera module. I’m using an HDMI to CSI-2 module and I’ve verified connectivity and operation with a Pi development board so the camera or the module itself I don’t think is the issue. I’m using an HDMI to CSI-2 module and I’ve verified connectivity and o…. IMX219 does not have Jetvariety board and does not need to install arducam driver, you can directly connect the camera to Jetson Nano and use it. During boot up, these messages appear which I think are related to the 1 I have an Arducam IMX219 camera. i2c: no acknowledge from address 0x10 May 20, 2024 · # Use the kernel's default instead. When I turn off my Jetson Nano from current completely, for example, for 10 minutes, and then switch on, dmesg tell me that: [ 1. Nov 24, 2020 · Hi - I just received my jetson nano 2gb a few days ago and I have not been able to establish a connection with a camera through the MIPI CSI-2 port. sh -k kernel-dtb jetson-xavier-nx-en715 Nov 24, 2020 · Hi - I just received my jetson nano 2gb a few days ago and I have not been able to establish a connection with a camera through the MIPI CSI-2 port. I will try how to configure CSI connector and let you know. Nov 24, 2020 · Thanks for your response. /flash. And this camera behaves a little strange. 337516] imx219 7-0010: tegracam sensor driver:imx219_v2. But I want to to do it on a Jetson NXwith a Quark carrier board. # This line should be removed if the legacy DWC2 controller is Oct 3, 2023 · Hello JerryChang, Thank you for your reply. 6 [ 1. 241013] imx219 6-0010: imx219_board_setup… Jul 3, 2020 · I have a new board and also have similar error Advise appreciated. I don’t have an imx219 sensor board so there’s the problem. It looks like this post HDMI 2 MIPI CSI Device Tree has some info. My setup is: Jetson Baseboard from capablerobots 15pin flex cable from capablerobots IMX219-AF from arducam Jetson Nano Nov 23, 2020 · I tried several things: Switching to another EN715 carrier board (just in case the board was broken) Flashing the Module via SDKManager (Jetpack 4.